Epson 410W Projector

From Longview ISD Technology Wiki

Revision as of 16:58, 9 January 2013 (view source) Jbinford (Talk | contribs) (→TroubleShooting) ← Older edit		Revision as of 17:11, 9 January 2013 (view source) Jbinford (Talk | contribs) (→TroubleShooting) Newer edit →
Line 19:		Line 19:
	== TroubleShooting ==		== TroubleShooting ==
	'''Projector Will Not Power On'''		'''Projector Will Not Power On'''
		+	# Make sure you do not see a light on the projector power button. ''See Image 1''
		+	# Use a yard stick to press the power button to see if it will turn on.
		+	# If not, the electric breaker may be thrown. '''Tell custodian'''
		+	# The power cord may be disconnected from the back of the projector. Check it.
		+	# The remote may need new batteries. Replace the batteries. ''See Image 2''
		+	# If the Lamp and Temp buttons are both blinking red, call the Help Desk!
		+	'''Projector Will Not Power Off'''
		+	# Use a yard stick to press the power button to see if it will turn off.
		+	# If it still will not turn off, the filter may be dirty and the projector overheating which is preventing powering off.
		+	# Call the Help Desk to remotely turn off the projector.
		+	# Clean the filter after the projector cools off.
		+	# If it cannot be remotely tuned off, unplug the power cord from the back of the projector. Wait for it to cool off and then clean filter.
		+	# Plug the power cord back in.
		+	# If it still doesn’t work correctly, turn in a tech help request.

---

Revision as of 17:11, 9 January 2013

Cleaning Filter

1. Turn off the projector and allow it to cool down.
2. The filter is located on the side of the projector that has the lamp.
3. As you face the whiteboard it is on the right side of the projector.
4. Slide the filter out, as shown. This allows both sides of the filter to be cleaned.

To clean the filter you can use:

• canned air (provide your own)
• blower (if available)
• small hand vacuum cleaner (if available)
• mouth – blow VERY, VERY hard!!
• DO NOT USE WATER to clean the filter!

To clean the vent Epson recommends using a small vacuum cleaner designed for computers and other office equipment. (Do this only if you can see dust & lint inside the vent after you remove the filter.)

TroubleShooting

Projector Will Not Power On

1. Make sure you do not see a light on the projector power button. See Image 1
2. Use a yard stick to press the power button to see if it will turn on.
3. If not, the electric breaker may be thrown. Tell custodian
4. The power cord may be disconnected from the back of the projector. Check it.
5. The remote may need new batteries. Replace the batteries. See Image 2
6. If the Lamp and Temp buttons are both blinking red, call the Help Desk!

Projector Will Not Power Off

1. Use a yard stick to press the power button to see if it will turn off.
2. If it still will not turn off, the filter may be dirty and the projector overheating which is preventing powering off.
3. Call the Help Desk to remotely turn off the projector.
4. Clean the filter after the projector cools off.
5. If it cannot be remotely tuned off, unplug the power cord from the back of the projector. Wait for it to cool off and then clean filter.
6. Plug the power cord back in.
7. If it still doesn’t work correctly, turn in a tech help request.

Image 1

Image 2

Image 3

Image 4

Image 5